High quality, Best service,Reasonable price.
Payment & Shipping Terms:
|Product Name:||CBM Drilling Rig||Type:||Rotary Drilling Rig|
|Power Type:||Diesel||Applications:||Oil And Gas,geothermy, Explotation And Mining|
rotary drilling rigs,
truck mounted drill rig
Rotary-drilling with reverse circulation CBM universal Drilling Rig TDR -50
The TDR -50 universal drilling rig enables each user to drill with the following methods, with borehole diameters of 3.5 ″to 47″and drilling depths up to 1 200m.
●Rotary-drilling with direct circulation
●Rotary-drilling with reverse circulation
●Percussion core drilling (ram coring)
●Wire-line core drilling
●Down-The-Hole hammer drilling
●Direction deviation drilling
TDR servies rig can be use for shallow oil and gas, coal bed methane drainage, geothermy, explotation of mine and large diameter deep water well application, also can be use for gas emissions of colliery and down hole of rescue.
TDR-50 Full Hydraulic Multifunction Top Drive Drill Rig
1. Unite Engine
Diesel engine, 6 cylinders, in-line, 2 valves, turbocharged intercooled; Separate cylinder heads, frame block; Using mechanical high-pressure injection technology for fuel system.
The crankshaft of diesel engine provides power for hydraulic pump through flexible coupler (made by KTR in Germany).
Model WD10G330E211 Diesel engine
Power 330 HP (243 Kw)@ 2200 RPM
Max.torque 1250 Nm@ 1500 RPM
Displacement 9.726 L
Min Fuel Consumption 210g/kw h
2. Hydraulic System
Four hydraulic pumps, three variable displacement piston pumps and one fixed displacement
hydraulic pumps, all together provide power for the rig. The hydraulic system is an open circuit with proportional control valve and completely circuit filter unit. The filter element can be replaced.
The heat dissipation of hydraulic is from forced air cooling. Variable displacement piston pump and proportional control valve of rotating and feeding system are load-sensitive designed,
which controls the flow of pump as required. All hydraulic branches are protected by overflow valve.
3. Outriggers and Mast Tilt
Outrigger is made by heavy square steel pipe, both front and rear cylinders are connected with the drill mounting. There are locking devices at both loading and travel position. Each outrigger could position all by itself.
The cylinder of mast has buffer end, which could reduce shock when it goes up and down, and makes it more stable. The control valve could change speed as needed.
4. Control Panel
Arc-swing panel located at the left side, and it can retract under the mast when transporting.
Control panel consists all the apparatus and driller position.The dash board consists: water-thermometer, tachometer, oil manometer, pressure gauge of rotating system, pressure
gauge of feeding system, pressure gauge of drilling system, pressure of drilling, Pressure
of assistant pump etc.
5. Telescoping Mast
Telescoping mast provides much more travel distance and height for the drill head, and
shortens the length of main machine in transportation. The sliding cylinder helps the mast
with travel distance up to 3.65 m, and makes it firmly contact the ground, accordingly,
minimizes the force of drill mounting.
Fully Expanded:62 feet (18.9 m)
Fully Retracted:39.4 feet (12 m)
6. Feeding System
Top drive head is driven by hydraulic cylinder and chain. When it is rising, the upper end of
mast could extended at the ratio of 1:2, the max length of head unit is about 46 foot (14.02m)
Capacity of pull back force 110 230 lbf (50 000Kg)
Capacity of pull down force 26 455 lbf (12 000Kg)
Max. Pull down speed 80m/min
Stroke of mast slip 3.65m
7. Safety System
Hydraulic system of mast is equipped with safety hydraulic valve, when something goes wrong
with hydraulic system and the rotate unit is drilling down out of control, the safety hydraulic
valve will lock the head unit, thus stops it from drilling down and avoids an accident.
8. Slow-Feeding Drill-Up Valve
The operator could control the pressure accurately through slowly feeding drill-up.
9. Top Drive Head
Top drive head suits for tricone bit, DTH hammer, PDC Dill bit and diamond bit which meets
special demand of rotate speed and torque during work. The 4-shift Gearbox using spur gear
drive, oil bath lubrication. Hydraulic Motor and gearbox could provide for much high speed
and torque to be adjusted.
The angle of rotate unit could be adjusted as needed, ranges from 0º(vertical)--90º.
Internal diameter of faucet core shaft: 76.2 mm
11. Power Wrench
The tongs are designed and manufactured according to SY/T5074 standard and API Spec 7K” Specification for Drilling and Well Servicing Equipment”.
Size Rang 3 1/2 ″coupling - 8″body
Max.Torque 100 000 Nm
Rotation Speed 2.7 – 40 RPM
12. Mounting: Crawler, Undercarriage of Excavator
Max.Moving speed is 3 Km/h.
13. Jib Boom
Hydraulic drive and control, 180º rotary support . Load capacity 7 605 lbf (3 450 Kg).
14. Floating Sub
Floating sub makes it possible for the joint to move at the range of 3 ″(76.2 mm).
The winch driven by hydraulic motor located behind the mast, using for lifting drilling tools ,such as rods , casing pipe, drill bit, and drill collar, etc. Operation of winch is independent of other drilling function.
Rope capacity of winch 50 m
Empty wheel pulling force 3450 kg
Empty wheel speed 60 m/min
steel cable 13 mm,35 m
16. Line Winch
The rig also is equipped with line winch, using for core drilling and other drilling field.
Max lifting capacity: 1.5 tons. (Bare Drum)
Steel wire Dia.: 6mm
Rope capacity: 1500m
Single wire lifting speed is 0-280m/min, it is stepless adjustable and used for lift and mount detecting devices.
17. Foam Pump
Foam pump is driven by hydraulic, Horizontal, triplex, single acting reciprocation piston pump.
Max displacement 75 L/min
Max pressure 6 Mpa
18. Tool Lubricator
Tool lubricator lubricating the drill tool for DTH hammer.
Lubricating oil flow:0-12 L/h
19. Electrical System
Generator and batter driven by diesel engine altogether provide 24V direct current. All cables are protected by seal line. Furthermore, all circuits are equipped with short-circuited.
Generator 24 V DC
Battery 2 batteries parallels connected with 12 V
Head lamp 4 halogen floodlight